|
Product Description
4pcs 3.7V Lithium Rechargable Battery, 852540 3.7V 1000mAh Battery with Protection Board and Insulated Rubber Tape Matched with ESP32 Development Board WIFI Kits for Arduino NodemcuFeatures:
1. Note: The maximum operating current of this battery is only about 1A, can not be used for unmanned aerial vehicles, model aircraft or power tools and other products that require high current.
2. This battery interface is JST 1.25 pitch male, it can be matched with some ESP32 Development Board that it come with Female JST 1.25 mm connectors.
Specification:
Standard Voltage: 3.7V
Rated Capacity: 1000mAh
Weight: About 17g
Size: 8.5*25*40(mm)
Working Current: 1.5A
Overcurrent protection: 2~3A
Overcharge limit pressure: 4.25±0.05V
Over-voltage limit pressure: 2.45±0.30V
Standard Charging Method: Charging this battery to 4.25V at 0.2C constant current, then charge the battery at a constant voltage of 4.2V till it's charging current≤ 0.05C.
Charge current time: Standard Charging: 0.2C (8 hours); Fast charging: 0.5C (2.5 hours).
The maximum charging current: 0.5C
Continuous Dishcarge Current: 0.5C
The maximum discharge current: 1C
End-off voltage: 2.75V/pcs
Allowable charging temperature: 0℃ ~ +45 ℃
Allowable discharge temperature: -10 ~ +60 ℃
Allowable storage temperature: -10 ~ +40 ℃( within 3 months); -10 ~ +30 ℃ ( within 6 months).
Package Including
4 * 1000mAh 852540 3.7V Lithium Rechargable Battery
Features
- Note: The battery overcurrent protection is not a panacea, do not continue to charge and discharge the current and voltage with a large current beyond the range, otherwise the protection board will be damaged and invalid
- 1000mAh: The recommended charging current is 0.2A, the maximum is not more than 1A. The discharge current is recommended 0.55A, and the maximum is not more than 3A
- Over-discharge protection: When the battery is about to run out and the voltage is as low as 3.0V, the protection board will also be turned off and can no longer be discharged, forming an over-discharge protection effect
- Overcharge protection: When charging the battery, when the voltage reaches the highest battery voltage (4.2V), the protection board will automatically power off and shut down, indicating that it will not continue to charge when fully charged, form an overcharge protection
- Short circuit protection: When an accidental short circuit occurs, the protection board will automatically shut down within a few milliseconds and will not be powered on again. Note that the cell is short-circuited (not through the protection board). The protection board will also fail due to continuous high current, or the components are heated and damaged
Customers Who Bought This Item Also Bought
- IZOKEE D1 Mini NodeMcu Lua 4M Bytes WLAN WIFI Internet Development Board Base on ESP8266 ESP-12F for Arduino, 100% Compatible with WeMos D1 Mini (Pack of 5) ...
- MakerFocus ESP8266 OLED WiFi Development Board 0.91 Inch ESP8266 OLED Display CP2102 Support Arduino IDE ESP8266 NodeMCU LUA
- 915MHz ESP32 LoRa 0.96 OLED Development Board WiFi Bluetooth SX1276 Transceiver Module + LoRa Antenna for Arduino LoraWan IOT Internet of Thing WIshioT (Pack of 2)
- HiLetgo ESP32 OLED WiFi Kit ESP-32 0.96 Inch Blue OLED Display WiFi+Bluetooth CP2012 Internet Development Board for Arduino ESP8266 NodeMCU
- HiLetgo ESP-WROOM-32 ESP32 ESP-32S Development Board 2.4GHz Dual-Mode WiFi + Bluetooth Dual Cores Microcontroller Processor Integrated with Antenna RF AMP Filter AP STA for Arduino IDE
- KeeYees ESP32 ESP-32S Development Board 2.4 GHz Dual Core WLAN WiFi + Bluetooth 2-in-1 Microcontroller ESP-WROOM-32 Chip CP2102 for Arduino (2PCS)
- ESP32 LoRa 32 (V2), ESP32 Development Board WIFI Bluetooth LoRa Dual Core 240MHz CP2102 with 0.96inch OLED Display included 868/915MHZ Antenna for Smart Cities, Smart Farms, Smart Home, and IoT Makers
- GPS Module GPS NEO-6M(Arduino GPS, Drone Microcontroller, GPS Receiver) Compatible with 51 Microcontroller STM32 Arduino UNO R3 with IPEX Antenna High Sensitivity for Navigation Satellite Positioning
- MakerFocus ESP32 Development Board Upgraded Version 8MB Flash, ESP32 WiFi Bluetooth, ESP32 OLED 0.96 Inch OLED Display CP2102 Internet for Arduino ESP8266 NodeMCU
- MakerFocus 10pcs TP4056 Charging Module with Battery Protection 18650 BMS 5V Micro USB 1A 186 50 Lithium Battery Charging Board
*If this is not the "MakerFocus 4pcs 3.7V Lithium Rechargable Battery JST1.25 Connector 2pin, 852540 3.7V 1000mAh Battery" product you were looking for, you can check the other results by clicking this link. Details were last updated on Jan 11, 2025 16:59 +08.