Quality Control Engineering

Features

• This unique free application is for all students across the world. It covers 86 topics of Quality Control in detail. These 86 topics are divided in 5 units.
• Each topic is around 600 words and is complete with diagrams, equations and other forms of graphical representations along with simple text explaining the concept in detail.
• This USP of this application is "ultra-portability". Students can access the content on-the-go from anywhere they like.
• Basically, each topic is like a detailed flash card and will make the lives of students simpler and easier.
• Some of topics Covered in this application are:
• 1. Quality Improvement and Statistics
• 2. Statistical Quality and Process Control
• 3. Control Charts
• 4. Charts for Variable such as (X,R charts)
• 5. Charts for Attributes such as (P,C charts)
• 6. Use of Control Charts
• 7. Process Capability Analysis
• 8. Principle of acceptance sampling
• 9. Producer’s and consumer’s risk and Average outgoing quality
• 10. Sampling Error
• 11. Single Sampling Plan
• 12. Sampling Plans
• 13. Double Sampling Plan
• 14. Sequential Sampling Plan
• 15. Acceptance sampling attributes
• 16. Acceptance sampling by variable
• 17. Difference between attribute and variable sampling plans
• 18. Introduction to Reliability
• 19. Product Life Cycle Curve or Bath tub curve
• 20. Relationship between the failure rate and the mean time between failures
• 21. Systems Reliability (Series & Parallel System)
• 22. Implications for Design
• 23. Redundancy in Reliability
• 24. Reliability based design
• 25. Introduction of Value Analysis
• 26. Defining Cost and Value
• 27. The Focus of Value Analysis
• 28. Use of Value Analysis (Within the business & Market induced Reasons)
• 29. Types Of Value Analysis
• 30. Related Tools and Techniques of Value Analysis
• 31. Application of Value Analysis
• 32. Basic Concept of TQM
• 33. Difference Between Quality Assurance And Quality Control
• 34. Implementation of TQM
• 35. Introduction of Implementation of TQM
• 36. Quality Assurance in TQM
• 37. Quality Control points- Introduction
• 38. Quality Management in TQM
• 39. Introduction to Total Quality Management
• 40. Historical evolution of Total Quality Management
• 41. Zero Defects in TQM
• 42. Introduction to Taguchi method
• 43. History of Six Sigma
• 44. Defination of Six Sigma
• 45. Concept of Sig Sigma
• 46. Introduction of ISO 9000
• 47. ISO 9000 Standard Series
• 48. Historical Background: The Concept of Quality Circle
• 49. Introduction of Quality Circle
• 50. Organizational Structure of Quality Circle
• 51. Material Quality Control
• 52. Diagnostic Techniques Introduction
• 53. Thomson, Rayleigh and Raman scattering
• 54. Diode laser absorption
• 55. (Ta)LIF
• 56. Absolute intensities of spectral lines
• 57. Spectral Line Broadening
• 58. Continuum radiation and Power Interruption
• 59. Introduction to Condition Monitoring
• 60. Introduction to Condition Monitoring Techniques
• 61. Mean Time Between Failures (MTBF)
• 62. Objectives of Inspection and types of Inspection
• 63. Stages of Inspection
• 64. Inspection Procedures
• 65. Methods of Inspection and its Drawbacks
• 66. Introduction of Quality and Quality Control
• 67. Quality Characteristics
• 68. Total Quality Control
• 69. Process capability Introduction
• 70. Definitions and Process Capability Study Steps
• 71. Process Capability and Calculating Process Capability Indices
• 72. Accuracy and Precision
• 73. Types of Fits
• 74. Types of Tolerances
• 75. Standard Tolerances
• 76. Selection of Fits
• 77. Systems of Fit (Hole and Shaft Basis)
• 78. Limits
• 79. Non Destructive Testing (NDT)
• 80. Non destructive Evaluation (NDE) Techniques
• 81. Types of Gauges
• 82. Interchangeability Introduction
• 83. Types of Interchangeability
• 84. Standardisation and its Types
• 85. Accuracy versus Precision
• 86. Design for Maintainability

*If this is not the "Quality Control Engineering" product you were looking for, you can check the other results by clicking this link.  Details were last updated on Nov 19, 2024 23:30 +08.